Bolt Remaps

Call 0203 038 8555 · WhatsApp 07719 156806 · 4.8 ★★★★★ 283 Google reviews · 6am–9pm, 7 days, including bank holidays

Peugeot and Citroën additive level code

P15B3: additive tank level/sensor fault on Peugeot and Citroën

Codes: P15B3, P1434, P1435

P15B3 is a Peugeot and Citroën code for the particulate filter additive tank. The engine ECU has calculated that the Eolys additive level is below its minimum, or it no longer trusts the level reading. It is not an AdBlue code. Often the tank is genuinely low or was refilled without a counter reset, but a split pouch or a pump that is not dosing can cause it too. We check live data before anything is replaced. Mobile diagnosis and repair from £249, fixed price, no fix no fee.

We diagnose first, at your vehicle. Fixed price before any work starts. No fix, no fee on the agreed outcome. Mobile to your drive, yard, depot or roadside, 6am to 9pm, 7 days including bank holidays.

Book mobile diagnosis: 0203 038 8555 · WhatsApp the code to 07719 156806

What P15B3 means in plain English

Many Peugeot and Citroën diesels with a particulate filter carry a small second tank next to the fuel tank. It holds Eolys additive, a cerium-based fluid that is dosed into the diesel every time you refuel. The additive helps the filter burn off trapped soot at a lower temperature, so it can clean itself during normal driving.

The car does not fit a simple float gauge to that tank. Instead, the engine ECU keeps a running tally. It knows roughly how much fluid was in the tank after the last refill, and it subtracts every dose it commands. When that calculated figure drops below a set minimum, or the ECU decides the level reading cannot be trusted, it stores P15B3. Tools word it slightly differently, so we always read the full manufacturer text.

The key point is that P15B3 is a calculation, not a measurement. The tank might really be empty, full with a counter that was never reset, or leaking. The code alone does not say which, so a refill sometimes fixes it and sometimes does nothing.

Symptoms you may notice

P15B3 often gives a warning long before the car feels any different.

  • Additive or particle filter message

    Messages such as "Particle filter additive level too low" or a general anti-pollution fault, usually with the engine or service light on.

  • "Risk of particle filter blocking"

    Once the ECU believes dosing has stopped, it warns that the filter may load up. This is the message that tends to make people call us.

  • Regenerations stop or fail

    With no additive in the fuel, soot burns less readily. The ECU may give up on regenerations, or they start and never finish, so soot loading creeps up journey by journey.

  • Reduced power or limp mode

    If the filter loads up far enough, the engine limits power to protect itself, often first noticed on hills or when loaded.

  • No change in how it drives, yet

    Plenty of cars with P15B3 drive normally for a while. This is the cheapest point to deal with it, before soot becomes the bigger problem.

How P15B3 relates to P1434 and P1435

All three codes belong to the same additive system, but each one describes a different part of it. Reading them together tells us where to start.

  • P15B3: the level calculation

    The ECU's sum says the tank is at or below minimum, or the level reading is not plausible. It describes the fluid, not the electrics.

  • P1434: pump supply and control circuit

    An electrical fault in the power, earth or control side of the additive pump. See our P1434 guide for how that circuit fails.

  • P1435: pump communication

    The engine ECU has lost reliable contact with a multiplexed pump, or the pump has reported a fault of its own. See our P1435 guide for the network side.

  • Why they can appear together

    If the pump stops dosing because of a wiring or network fault, the ECU's level sums and the real fluid stop agreeing, and P15B3 can be stored alongside P1434 or P1435. An empty tank can also make a pump report a fault. When companion codes are present, we fix the cause they point to before we treat P15B3 as a fluid problem.

Common causes, most likely first

This is the order we work through them in. We do not put percentages on it, because every car's history is different.

  • 1. Tank empty, or refilled without a counter reset

    The fluid simply ran out at the expected mileage, or someone topped it up and the ECU was never told. Without the reset, the calculated level stays at minimum and the code returns however full the tank is.

  • 2. Split or leaking additive pouch

    Later systems hold the fluid in a flexible pouch inside a rigid housing. If the pouch or a line splits, fluid is lost much sooner than the ECU expects. A refill on top of a leak just drains away again.

  • 3. Level sensing or quantity calculation fault

    The ECU relies on refuel detection and its own stored values to work out the level. If those inputs are wrong, or the stored values are corrupt, the result can be nonsense even with a healthy tank.

  • 4. Pump not dosing as commanded

    A pump that is not working means the real level and the calculated level drift apart. This is where P1434 or P1435 normally shows up as well, and the pump circuit becomes the priority.

  • 5. Wrong fluid in the tank

    Older and newer systems use different additive types. The wrong fluid, or a non-approved one, can upset dosing and leave the system reporting a fault. We confirm the correct fluid by VIN before anything goes in.

  • 6. Part changed but not learned

    After a pump, tank or ECU swap, the new part has to be coded and the additive counter set. If that step was skipped, P15B3 can stay stored even though the hardware is new.

Eolys additive is not AdBlue

P15B3 belongs to the particulate filter additive system, not to the AdBlue (SCR) exhaust system. Eolys goes into the diesel to help the filter burn soot. AdBlue goes into the exhaust to cut NOx. They have different tanks, different fluids and different codes.

Many newer Peugeot and Citroën diesels have both, so they are easy to mix up. Topping up AdBlue will not cure P15B3. If your dash counts down miles to a no-start or mentions AdBlue, that is the other system.

Eolys additive (P1435)AdBlue / SCR
What it doesHelps the particulate filter burn off sootConverts NOx in the exhaust into nitrogen and water
Where the fluid goesInto the diesel fuel tank, at each refuelSprayed into the exhaust, ahead of the SCR catalyst
The fluidCerium-based additive (Eolys)32.5% urea solution (AdBlue / DEF)
Who tops it upWorkshop only, with a counter resetThe driver, through the blue filler
Typical codesP1435, P1434, U0118, P15B3P20EE, P20E8, P207F, P20BA
If ignoredBlocked particulate filter, limp modeCountdown to a no-start

How we diagnose P15B3 with live data

We work it out at your vehicle with manufacturer-level diagnostics, proving why the ECU thinks the tank is low before any repair.

  • Check the car's equipment by VIN

    Not every Peugeot or Citroën diesel has an additive tank. We confirm the system is fitted, which generation it is and which fluid it needs.

  • Full scan with exact fault text

    We read every module, not just the engine. P15B3 on its own points one way. P15B3 with P1434, P1435 or a network code points another.

  • Additive level and refill history

    We read the calculated additive quantity, the stored refill data and the distance since the last reset, then compare that against what is physically in the tank.

  • Pump test

    We command the pump from the tool and watch the response. A pump that doses on command rules out the pump and its circuit as the reason the level dropped.

  • Leak and pouch inspection

    We look at the tank housing, pouch area, lines and the ground under the tank for signs of lost fluid before any refill goes in.

  • Filter condition

    We read soot loading and differential pressure, so we know whether the filter has loaded up while the additive was low and needs a regeneration afterwards.

The typical repair path

Diagnosis first, then a fixed price before any work starts. No fix, no fee on the agreed outcome.

We come to your drive, yard, depot or roadside, 6am to 9pm, 7 days. Most P15B3 jobs that turn out to be fluid and counter problems are finished in the same visit. If a pouch, tank assembly or pump has to be ordered, we confirm it with you on the first visit, agree the price, and come back to fit and code it.

  • Refill and counter reset

    Where the tank is simply low or the reset was missed, we fill it with the correct approved additive and reset the counter with diagnostic equipment, then confirm the calculated level reads correctly.

  • Pouch or tank repair or replacement, if proved

    Only when we have found the leak or damage. The new part is fitted, primed and coded so the ECU recognises it and the counter starts from the right figure.

  • Wiring or pump work, only if a companion code proves it

    If P1434 or P1435 is present and testing confirms a circuit or pump fault, we repair that first. Without that evidence we do not quote a pump for P15B3.

  • Regeneration and road test, if needed

    If soot has built up, we run a service regeneration once dosing works again, clear the codes and confirm on a test drive that nothing returns.

  • Mobile diagnosis and straightforward fix: From £249 Callout, live-data diagnosis and fixes such as a refill with the correct fluid and a counter reset.
  • Additive pouch or tank assembly: Fixed price after diagnosis Quoted only once a leak or failed part has been found and matched to your VIN.
  • Service regeneration if soot is high: Quoted on the day Only needed if the filter loaded up while the additive was low.

Models we see P15B3 on

P15B3 turns up on Peugeot and Citroën diesels that use the Eolys additive system. The ones we are asked about most are the Peugeot 308, Partner and Boxer, and the Citroën Berlingo, Relay and Dispatch, along with sister vans that share the same engines and additive system.

Not every version has an additive tank. The 2019 onwards Berlingo and Partner with the 1.5 BlueHDi generally do not. We confirm the system by VIN before quoting.

P15B3 questions

What does P15B3 mean on a Peugeot or Citroën?

It means the engine ECU has calculated that the Eolys additive in the particulate filter additive tank is below its minimum, or it no longer trusts the level reading. The tank may be empty, unreset after a refill, or losing fluid.

Is P15B3 an AdBlue fault?

No. P15B3 belongs to the Eolys particulate filter additive system, which is mixed into the diesel. AdBlue is a separate exhaust system with its own tank and its own codes, such as P20EE.

Can I keep driving with P15B3?

Usually for a short while, but without additive the particulate filter loads up faster. If it blocks, you risk limp mode and a much bigger repair. Book a diagnosis as soon as you can.

Will clearing the code fix P15B3?

No. The ECU's level calculation stays the same, so the code comes back. It only clears properly once the fluid is correct and the counter has been reset, or the leak or fault behind it is repaired.

Can I top the additive up myself?

Topping up alone rarely works. The ECU needs its counter reset with diagnostic equipment, and the fluid type depends on your system. We refill with the correct approved additive and reset it in the same visit.

How is P15B3 different from P1434 and P1435?

P15B3 is about the calculated additive level. P1434 is an electrical fault in the pump's supply or control circuit. P1435 is a communication or pump-reported fault. A pump fault can lead to P15B3, so we check for the other two first.

Book mobile diagnosis: 0203 038 8555 · WhatsApp the code to 07719 156806