"Emissions System Fault" on a Diesel: Which System Is It?
Warnings and symptoms · Published
By the Bolt Remaps technical team · Last updated:
The generic emissions warning can come from four different systems: AdBlue and SCR, the DPF, the EGR valve, or the NOx and temperature sensors. The stored fault code tells you which one it is.
In short
- "Emissions system fault" is a catch-all message. It does not name the part.
- The fault code is what separates an AdBlue problem from a DPF, EGR or sensor problem.
- A countdown in miles almost always means the SCR (AdBlue) system, and it will end in a no-start.
- Emissions faults matter for the MOT, and tampering with the systems is illegal.
What the warning actually tells you
Makers use a handful of vague messages: "Emissions system fault", "Check emissions system", "Exhaust fluid system fault", or just the engine light with a mileage countdown underneath. They are deliberately general. The dash has room for one line, and the engine computer is telling you that something in the exhaust clean-up chain is out of limits.
There are four candidates on a modern diesel van. The SCR system uses AdBlue to cut NOx. The diesel particulate filter (DPF) traps soot. The EGR valve feeds some exhaust back into the intake to lower combustion temperatures. Then there are the NOx and exhaust temperature sensors that all of those systems rely on.
The message alone will not tell you which of the four has failed. The stored fault code will, so reading it is always step one. Our AdBlue dashboard warnings guide shows the wording each maker uses.
How the codes point you to the system
These are the codes behind most emissions warnings we are called to, and what they usually turn out to be once we are on the driveway.
P20E8: dosing pressure too low
The AdBlue pump cannot build or hold pressure. On the van it is usually a pump that has failed, a blocked filter in the tank unit, crystals in a line or a wiring fault to the pump. See P20E8 low dosing pressure.
P20EE: SCR efficiency below threshold
The catalyst is not cutting NOx as much as it should. The usual causes are a lazy NOx sensor, an injector that is not spraying properly, poor fluid or a catalyst coated in deposits. P20EE explained goes through the order we test them in.
P2BAD: NOx exceedance
The computer has seen too much NOx coming out of the tailpipe for too long. It is a result, not a cause, so we look for what is stopping the SCR system working. Read more on P2BAD NOx exceedance.
P207F: reductant quality
The quality sensor in the tank thinks the fluid is wrong. Diluted or old AdBlue is common, but a failing quality sensor gives the same code. P207F fluid quality faults explains how we tell the two apart.
P229F: NOx sensor 2 range
The NOx sensor after the catalyst is reading out of range. It is often the sensor itself, but an exhaust leak or a wiring fault can do it too. See P229F downstream NOx sensor.
P2463 and P2452: DPF soot or pressure sensor
These point at the particulate filter, not AdBlue. Either the filter is loaded with soot or the differential pressure sensor and its pipes are giving false readings.
P0400 to P0402: EGR flow
The EGR valve is stuck, sooted up or not moving the way the computer asked. Power loss and smoke often come with it.
Warning, system and whether to keep driving
Use this as a rough guide only. If the van drives differently, smokes, smells hot or shows a flashing light, stop and get it checked.
| Warning or code | System | Usual cause | Keep driving? |
|---|---|---|---|
| Countdown in miles | SCR (AdBlue) | Any confirmed SCR fault | Only to plan a repair before it reaches zero |
| P20E8 | SCR (AdBlue) | Pump, blocked line or filter, wiring | Short trips, book soon |
| P20EE | SCR (AdBlue) | NOx sensor, injector, fluid, catalyst | Short trips, book soon |
| P2BAD | SCR (AdBlue) | Whatever stopped the SCR working | Short trips, book soon |
| P207F | SCR (AdBlue) | Wrong or diluted fluid, quality sensor | Do not top up further until checked |
| P229F | NOx sensor | Sensor, exhaust leak, wiring | Short trips, book soon |
| P2463 / DPF light | DPF | Soot load from short trips | A steady run may help; stop if power drops |
| P0400 to P0402 | EGR | Sticking or sooted valve | Gently; get it checked |
Why a countdown changes things
If the warning comes with a number of miles, treat it as urgent. That countdown is the SCR system's legal enforcement strategy. When it reaches zero, most vans will not restart after the engine is switched off. Our page on the AdBlue countdown explains how many miles you usually get and what happens at the end.
Clearing the code with a reader does not reset the counter on most vans. The countdown only stops once the fault is fixed and the system has confirmed it is working again.
When it isn't the AdBlue system
Plenty of emissions warnings have nothing to do with AdBlue. A DPF light on a van that only does short local runs is usually soot, and a long steady drive or a forced regeneration can sort it. A cracked pressure pipe on the DPF sensor is a cheap part that sets off a lot of alarm.
An EGR fault on some engines is a valve and cooler job that needs the intake taking apart. Depending on the van, that may be better done in a workshop than on a driveway, and we will say so.
If the code points at the engine itself, such as misfire, fuel pressure or a turbo fault, the emissions warning is only a side effect. We will tell you that rather than chase the exhaust.
The MOT and the law
An engine or emissions warning light that stays on can fail the MOT, and a fault in these systems can also make the van fail the emissions test. The exact rules depend on the van's age, which our MOT page sets out.
Switching off, bypassing or tampering with the SCR, DPF or EGR systems is illegal for road use in the UK. It fails the MOT and can void your insurance. The legal fix is to find the faulty part and repair it. Read AdBlue, the MOT and the law and our plain answer on whether disabling AdBlue is legal.
When to call us
Mobile AdBlue diagnosis and repair from £249. No fix, no fee. 6am to 9pm, 7 days, across London and the South East. We are IMI affiliated and have 7+ years of experience fixing these faults at the customer's vehicle.
We scan every module, check live data and tell you which system is at fault before any work starts. If your code is P20EE, our article on SCR efficiency below threshold is worth reading first. Check our AdBlue repair prices or get a fixed price.
Common questions
What does "emissions system fault" mean on a diesel van?
It means the engine computer has found a problem somewhere in the exhaust clean-up systems: the AdBlue SCR system, the DPF, the EGR valve or the NOx and temperature sensors. The message itself is generic. The stored fault code is what tells you which system is involved and roughly what has gone wrong, so get it read before buying parts.
Can I drive with an emissions system fault?
Usually for short distances, but get it diagnosed soon. If there is a mileage countdown, the van may not restart once it hits zero. If the van is losing power, smoking, smelling hot or the light is flashing, stop driving it. Driving for weeks on a fault can turn a sensor repair into a bigger job.
Is an emissions fault always AdBlue?
No. Many emissions warnings come from a sooty DPF, a sticking EGR valve or a faulty sensor. A countdown in miles almost always points at the AdBlue SCR system, but without one it could be any of the four. The fault code and live data are the only reliable way to tell.
Will my van fail its MOT with an emissions warning?
It may. An engine or emissions warning light that stays on can fail the MOT, depending on the van's age, and a fault in these systems can also cause an emissions test failure. Tampering with the systems is a fail and is illegal for road use. Fixing the underlying fault properly before the test is the only safe route.
Can clearing the code fix an emissions fault?
No. Clearing a code only removes the record. If the fault is still there, the computer sees it again and the warning returns, often within one drive. On most vans clearing the code also does not reset an AdBlue countdown. The fault has to be found and repaired first.